Want to Pass 300-101 Exam In Next HOURS? Get it now →
November 18, 2018

Questions Ask for 300 101 dumps

Cause all that matters here is passing the Cisco ccnp route 300 101 pdf exam. Cause all that you need is a high score of route 300 101 ROUTE Implementing Cisco IP Routing exam. The only one thing you need to do is downloading Exambible ccnp route 300 101 dumps pdf exam study guides now. We will not let you down with our money-back guarantee.

P.S. Exact 300-101 testing engine are available on Google Drive, GET MORE: https://drive.google.com/open?id=1PpU_6uksdH22QCdKrEcnWjPvNnVGXp8m


New Cisco 300-101 Exam Dumps Collection (Question 3 - Question 12)

Q3. You have been asked to evaluate how EIGRP is functioning in a customer network.

What is the advertised distance for the 192.168.46.0 network on R1?

A. 333056

B. 1938688

C. 1810944

D. 307456

Answer: A


Q4. Which PPP authentication method sends authentication information in clear text?

A. MS CHAP

B. CDPCP

C. CHAP

D. PAP

Answer: D

Topic 3, Layer 3 Technologies

20.Scenario:

You have been asked to evaluate an OSPF network setup in a test lab and to answer questions a customer has about its operation. The customer has disabled your access to the show running-config command.

How old is the Type 4 LSA from Router 3 for area 1 on the router R5 based on the output you have examined?

A. 1858

B. 1601

C. 600

D. 1569


Q5. Which statement is true about the PPP Session Phase of PPPoE?

A. PPP options are negotiated and authentication is not performed. Once the link setup is completed, PPPoE functions as a Layer 3 encapsulation method that allows data to be transferred over the PPP link within PPPoE headers.

B. PPP options are not negotiated and authentication is performed. Once the link setup is completed, PPPoE functions as a Layer 4 encapsulation method that allows data to be transferred over the PPP link within PPPoE headers.

C. PPP options are automatically enabled and authorization is performed. Once the link setup is completed, PPPoE functions as a Layer 2 encapsulation method that allows data to be encrypted over the PPP link within PPPoE headers.

D. PPP options are negotiated and authentication is performed. Once the link setup is completed, PPPoE functions as a Layer 2 encapsulation method that allows data to be transferred over the PPP link within PPPoE headers.

Answer: D


Q6. Which feature can mitigate fragmentation issues within network segments that are between GRE endpoints?

A. PMTU

B. ICMP DF bit

C. TCP Flow Control

D. TCP MSS

Answer: D


Q7. Refer to the exhibit.

Based on this FIB table, which statement is correct?

A. There is no default gateway.

B. The IP address of the router on FastEthernet is 209.168.201.1.

C. The gateway of last resort is 192.168.201.1.

D. The router will listen for all multicast traffic.

Answer: C


Q8. A network administrator executes the command clear ip route. Which two tables does this command clear and rebuild? (Choose two.)

A. IP routing

B. FIB

C. ARP cache

D. MAC address table

E. Cisco Express Forwarding table

F. topology table

Answer: A,B


Q9. CORRECT TEXTROUTE.com is a small IT corporation that has an existing enterprise network that is running IPv6 0SPFv3. Currently OSPF is configured on all routers. However, R4's loopback address (FEC0:4:4) cannot be seen in R1's IPv6 routing table. You are tasked with identifying the cause of this fault and implementing the needed corrective actions that uses OPSF features and does not change the current area assignments. You will know that you have corrected the fault when R4's loopback address (FEC0:4:4) can be seen in RTs IPv6 routing table.

Special Note: To gain the maximum number of points you must remove all incorrect or unneeded configuration statements related to this issue.

Answer:

Here is the solution below:

Explanation:

To troubleshoot the problem, first issue the show running-config on all of 4 routers. Pay more attention to the outputs of routers R2 and R3 The output of the "show running-config" command of R2:

The output of the "show running-config" command of R3:

We knew that all areas in an Open Shortest Path First (OSPF) autonomous system must be physically connected to the backbone area (Area 0). In some cases, where this is not possible, we can use a virtual link to connect to the backbone through a non-backbone area. The area through which you configure the virtual link is known as a transit area. In this case, the area 11 will become the transit area. Therefore, routers R2 and R3 must be configured with the area <area id> virtual-link <neighbor router-id>command. + Configure virtual link on R2 (from the first output above, we learned that the OSPF process ID of R2 is 1):

R2>enable R2#configure terminal

R2(config)#ipv6 router ospf 1

R2(config-rtr)#area 11 virtual-link 3.3.3.3 Save the configuration:

R2(config-rtr)#end

R2#copy running-config startup-config

(Notice that we have to use neighbor router-id 3.3.3.3, not R2's router-id 2.2.2.2) + Configure virtual link on R3 (from the second output above, we learned that the OSPF process ID of R3 is 1 and we have to disable the wrong configuration of "area 54 virtual-link 4.4.4.4"):

R3>enable R3#configure terminal

R3(config)#ipv6 router ospf 1

R3(config-rtr)#no area 54 virtual-link 4.4.4.4

R3(config-rtr)#area 11 virtual-link 2.2.2.2 Save the configuration:

R3(config-rtr)#end

R3#copy running-config startup-config

You should check the configuration of R4, too. Make sure to remove the incorrect configuration statements to get the full points.

R4(config)#ipv6 router ospf 1

R4(config-router)#no area 54 virtual-link 3.3.3.3 R4(config-router)#end

After finishing the configuration doesnu2019t forget to ping between R1 and R4 to make sure they work.

Note. If you want to check the routing information, use the show ipv6 route command, not "show ip route".


Q10. Which two statements about Frame Relay LMI autosense are true on a Router? (Choose two)

A. It requires the LMI type to be explicitly configured.

B. It operates on Frame Relay DTE interfaces.

C. It operates on Frame Relay DCE interfaces.

D. It operates when the line is up by the line protocol is down.

E. It requires the line protocol to be up.

Answer: B,D

Explanation: https://www.cisco.com/c/en/us/td/docs/ios/12_2/wan/configuration/guide/fwan_c/wcffrely.ht ml


Q11. R3#show run | include defaultip default-network 140.140.0.0

ip default-network 130.130.0.0 R3#show ip route | begin Gateway

Gateway of last resort is 0.0.0.0 to network 130.130.0.0 116.0.0.0/8 is variably subnetted, 5 subnets, 3 masks C 116.16.37.0/30 is directly connected, Serial1/0.2

C 116.16.32.0/30 is directly connected, Serial2/0.2 C 116.16.34.0/28 is directly connected, Serial1/0.1 C 116.16.35.0/28 is directly connected, Serial2/0.1 S 116.0.0.0/8 [1/0] via 116.16.34.0

* 140.140.0.0/32 is subnetted, 3 subnets

O 140.140.1.1 [110/65] via 116.16.34.4, 00:14:54, Serial1/0.1

O 140.140.3.1 [110/65] via 116.16.34.4, 00:14:54, Serial1/0.1

O 140.140.2.1 [110/65] via 116.16.34.4, 00:14:54, Serial1/0.1

* 130.130.0.0/16 is variably subnetted, 4 subnets, 2 masks D* 130.130.0.0/16 is a summary, 00:30:04, Null0

C 130.130.1.0/24 is directly connected, Ethernet0/0

C 130.130.2.0/24 is directly connected, Ethernet0/1 C 130.130.3.0/24 is directly connected, Ethernet1/0

D 150.150.0.0/16 [90/679936] via 116.16.35.5, 00:02:58, Serial2/0.1

Refer to the exhibit. Why is the 140.140.0.0 network not used as the gateway of last resort even though it is configured first?

A. The last default-network statement will always be preferred.

B. A route to the 140.140.0.0 network does not exist in the routing table.

C. Default-network selection will always prefer the statement with the lowest IP address.

D. A router will load balance across multiple default-networks; repeatedly issuing the show ip route command would show the gateway of last resort changing between the two networks.

Answer: B

Explanation:

As you can see in the exhibit, 140.140.0.0 doesnu2019t appear in the routing table.


Q12. Which two statements about Frame Relay Point-to-Point connections are true? (Choose Two)

A. Changing a point-to-point sub interface to a different type requires the device to be reloaded.

B. They use two DLCIs to communicate with multiple endpoints over the Frame Relay cloud.

C. The device can establish a point-to-point connection to the cloud without a DLCI.

D. They can operate normally without a DLCI map.

E. Each physical interface that extends to the Frame Relay cloud can support a single SVC.

Answer: A,B



see more http://www.ubraindumps.com/300-101-dumps/

P.S. Easily pass 300-101 Exam with Examcollection Exact Dumps & pdf vce, Try Free: http://www.examcollectionuk.com/300-101-vce-download.html (487 New Questions)