Want to Pass 100-105 Exam In Next HOURS? Get it now →
May 11, 2018

The Only Tip You Need: 105 100

Master the 100 105 icnd1 ICND1 Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) content and be ready for exam day success quickly with this Ucertify icnd1 100 105 pdf exam. We guarantee it!We make it a reality and give you real 105 100 questions in our Cisco cisco 100 105 braindumps.Latest 100% VALID Cisco icnd1 100 105 pdf Exam Questions Dumps at below page. You can use our Cisco 100 105 icnd1 pdf braindumps and pass your exam.

P.S. Downloadable 100-105 rapidshare are available on Google Drive, GET MORE: https://drive.google.com/open?id=10aMCxNhtGaQ1g5X4WURwuSZDkYQMo5JZ


New Cisco 100-105 Exam Dumps Collection (Question 3 - Question 12)

Question No: 3

Which statement about routing protocols is true?

A. Link-state routing protocols choose a path by the number of hops to the destination.

B. OSPF is a link-state routing protocol.

C. Distance-vector routing protocols use the Shortest Path First algorithm.

D. IS-IS is a distance-vector routing protocol.

Answer: B


Question No: 4

WAN data link encapsulation types include which of the following? (Choose two.)

A. T1

B. Frame Relay

C. DSL

D. PPP

E. ISDN

Answer: B,D


Question No: 5

Which option is the default switch port port-security violation mode?

A. shutdown

B. protect

C. shutdown vlan

D. restrict

Answer: A

Explanation:

Shutdownu2014This mode is the default violation mode; when in this mode, the switch will automatically force the switchport into an error disabled (err-disable) state when a violation occurs. While in this state, the switchport forwards no traffic. The switchport can be brought out of this error disabled state by issuing the errdisable recovery cause CLI command or by disabling and reenabling the switchport.

Shutdown VLANu2014This mode mimics the behavior of the shutdown mode but limits the error disabled state the specific violating VLAN.


Question No: 6

Refer to the exhibit. The network administrator must complete the connection between the RTA of the XYZ Company and the service provider. To accomplish this task, which two devices could be installed at the customer site to provide a connection through the local loop to the central office of the provider? (Choose two.)

A. WAN switch

B. PVC

C. ATM switch

D. multiplexer

E. CSU/DSU

F. modem

Answer: E,F


Question No: 7

Scenario:

You are a junior network engineer for a financial company, and the main office network is experiencing network issues. Troubleshoot the network issues.

Router R1 connects the main office to the internet, and routers R2 and R3 are internal routers.

NAT is enabled on router R1.

The routing protocol that is enabled between routers R1, R2 and R3 is RIPv2.

R1 sends the default route into RIPv2 for the internal routers to forward internet traffic to R1.

You have console access on R1, R2 and R3 devices. Use only show commands to troubleshoot the issues.

Users complain that they are unable to reach internet sites. You are troubleshooting internet connectivity problem at main office. Which statement correctly identifies the problem on Router R1?

A. Interesting traffic for NAT ACL is incorrectly configured.

B. NAT configurations on the interfaces are incorrectly configured

C. NAT translation statement incorrectly configured.

D. Only static NAT translation configured for the server, missing Dynamic NAT or Dynamic NAT overloading for internal networks.

Answer: B


Question No: 8

Which statement about static routes is true?

A. The source interface can be configured to make routing decisions.

B. A subnet mask is entered for the next-hop address.

C. The subnet mask is 255.255 255.0 by default

D. The exit interface can be specified to indicate where the packets will be routed.

Answer: D

Explanation:

Static routing can be used to define an exit point from a router when no other routes are available or necessary. This is called a default route.


Question No: 9

Refer to the exhibit.

A network technician is unable to ping from R1 to R2. What will help correct the problem?

A. Ensure that the serial cable is correctly plugged in to the interfaces.

B. Apply the clock rate 56000 configuration command to the serial0/1 interface of R1.

C. Configure the serial0/1 interfaces on R1 and R2 with the no shutdown command.

D. Change the address of the serial0/1 interface of R1 to 192.1.1.4.

E. Change the subnet masks of both interfaces to 255.255.255.240.

Answer: A


Question No: 10

Based on the network shown in the graphic

Which option contains both the potential networking problem and the protocol or setting that should be used to prevent the problem?

A. routing loops, hold down timers

B. Switching loops, split horizon

C. routing loops, split horizon

D. Switching loops, VTP

E. routing loops, STP

F. Switching loops, STP

Answer: F


Question No: 11

Refer to the exhibit.

A network technician is unable to ping from R1 to R2. Using the output of the show interfaces serial0/1 command, what should the administrator do to correct the problem?

A. Replace the serial cable between R1 and R2.

B. Reseat the serial connectors on the R1 and R2 routers.

C. Configure the serial0/1 interface on R2 with the no shutdown command.

D. Configure the serial0/1 interface on R1 with the clock rate 56000 command.

E. Configure the serial0/1 interface on R1 with the ip address 192.1.1.7 255.255.255.252 command.

Answer: C


Question No: 12

Refer to the exhibit.

What value should be displayed in Box 1 of the ipconfig output of host A?

A. 172.18.14.5

B. 172.18.14.6

C. 192.168.1.10

D. 192.168.1.11

E. 192.168.1.250

F. 192.168.1.254

Answer: F



see more http://www.ubraindumps.com/100-105-dumps/

P.S. Easily pass 100-105 Exam with Dumpscollection Downloadable Dumps & pdf vce, Try Free: http://www.dumpscollection.net/dumps/100-105/ (347 New Questions)