Want to Pass NSE7 Exam In Next HOURS? Get it now →
October 11, 2017

[Most up-to-date] nse7 fortinet

Want to know Ucertify nse7 fortinet Exam practice test features? Want to lear more about Fortinet Fortinet Troubleshooting Professional certification experience? Study Refined Fortinet fortinet nse7 answers to Replace fortinet nse7 questions at Ucertify. Gat a success with an absolute guarantee to pass Fortinet fortinet nse7 (Fortinet Troubleshooting Professional) test on your first attempt.

Q21. Examine the following partial output from two system debug commands; then answer the question below. 

Which of the following statements are true regarding the aboveoutputs? (Choose two.) 

A. The unit is running a 32-bit FortiOS 

B. The unit is in kernel conserve mode 

C. The Cached value is always the Active value plus the Inactive value 

D. Kernel indirectly accesses the low memory (LowTotal) through memory paging 

Answer: A,C 


Q22. Examine the IPsec configuration shown in the exhibit; then answer the question below. 

An administrator wants to monitor the VPN byenable the IKE real time debug using these commands: 

diagnose vpn ike log-filter src-addr4 10.0.10.1 diagnose debug application ike -1 diagnose debug enable 

The VPN is currently up, there is no traffic crossing the tunnel and DPD packets are being interchanged between both Ipsec gateways. However, the IKE rea time debug does NOT show any output. Why isn't there any output? 

A. The IKE real time debug shows the phases 1 and 2 negotiations only. It does not show any more output once the tunnel is up. 

B. The log-filter setting is set incorrectly. The VPN's traffic does not match this filter. 

C. The IKF real time debug shows the phase 1 negotiation only. For information after that, the administrator must use the IPsec real time debug instead: diagnosedebug application ipsec -1 

D. The IKE real time debug shows error messages only. If it does not provide any output, it indicates that the tunnel is operating normally. 

Answer:


Q23. Examine the IPsec configuration shown in the exhibit; then answer the question below. 

An administrator wants to monitor the VPN byenable the IKE real time debug using these commands: 

diagnose vpn ike log-filter src-addr4 10.0.10.1 diagnose debug application ike -1 diagnose debug enable 

The VPN is currently up, there is no traffic crossing the tunnel and DPD packets are being interchanged between both Ipsec gateways. However, the IKE rea time debug does NOT show any output. Why isn't there any output? 

A. The IKE real time debug shows the phases 1 and 2 negotiations only. It does not show any more output once the tunnel is up. 

B. The log-filter setting is set incorrectly. The VPN's traffic does not match this filter. 

C. The IKF real time debug shows the phase 1 negotiation only. For information after that, the administrator must use the IPsec real time debug instead: diagnosedebug application ipsec -1 

D. The IKE real time debug shows error messages only. If it does not provide any output, it indicates that the tunnel is operating normally. 

Answer:


Q24. When does a RADIUS server send anAccess-Challengepacket? 

A. The server does not have the user credentials yet. 

B. The server requires more information from the user,such as the token code for two-factor authentication. 

C. The user credentials are wrong. 

D. The user account is not found in the server. 

Answer:


Q25. Examine the following routing table and BGP configuration; then answer the question below. 

TheBGP connection is up, but the local peer is NOT advertisingthe prefix 192.168.1.0/24. Which configuration change will make the local peer advertise this prefix? 

A. Enable the redistribution of connected routers into BGP. 

B. Enable the redistribution of static routers into BGP. 

C. Disable the setting network-import-check. 

D. Enable the setting ebgp-multipath. 

Answer:


Q26. What configuration changes can reduce the memory utilization in a FortiGate? (Choose two.) 

A. Reduce the session time to live. 

B. Increase the TCP session timers. 

C. Increase the FortiGuard cache time to live. 

D. Reduce the maximum file size to inspect. 

Answer: A,D


Q27. A FortiGate device has the following LDAP configuration: 

Based on the output, what FortiGate LDAP setting is configured incorrectly? 

A. cnid. 

B. username. 

C. password. 

D. dn. 

Answer:



see more http://www.ubraindumps.com/NSE7-dumps/